Designing an automated system to fit up to 36,000 protective caps per day onto office chair castors might seem an unusual and challenging application for servo drives and controllers. However, it’s a good example of how today’s motion control and automation technology can help manufacturers’ to increase productivity and reduce costs.

Bulky objects such as office chairs require cumbersome cardboard packaging to ensure they are delivered to customers without any damage caused during transportation. Drives and Motors specialists YASKAWA played a key role in the development of an automated system specifically designed to fit protective plastic caps onto the castors with their Sigma-7 series servo-drives and a SLIO-series controller.

Gross+Froelic, is an office chair and furniture castor specialist who wanted to explore the benefits of the latest automation technology for their manufacturing processes, such as applying a system which applies ring-shaped protective caps. Any ‘bulky’ furniture item with castors doesn’t have to be carried, although you wouldn’t push a typical office chair all the way to a customer! However, once delivered they can certainly be wheeled to their final destination, but, must arrive without any scratches or damage, hence the need for plastic protectors. 

The castors consist of two individual wheels with a protective cap pressed onto each and it’s now a process which can be performed automatically and at considerable speed. Gross+Froelich use a machine made by ARAMIS which can operate with cycle times of just 2.4 seconds, following its re-design using the latest servo technology.

Depending on the castor model, it’s now possible to fully apply up to 36,000 protective caps automatically to the castor wheels over 24 hours of operation. This is an increase of around 10,000 caps more than the machine managed, before it’s re-design. So what were the two key factors which helped to achieve shorter cycle times? Firstly the capacity of the rotary indexing table for the plastic caps was increased from four receptacles to eight and secondly, three of the pneumatic drives installed in the machine were replaced with the more dynamic Yaskawa Sigma-7 series electrical servo drives.

It would have been impossible to achieve the higher speeds with pneumatic drives due to the mechanical stresses being excessively high. Furthermore, the levels of compressed air consumption are much lower which has reduced operating costs.

Yaskawa’s Sigma-7 series was the choice for the electric drives having already proven themselves in many similar applications and impressed ARAMIS the machine builder. Features such as rapid commissioning, high production capacity and maximum operational reliability, in addition to the responsiveness of the AC motors, were the key factors for the machine builder. Their extremely compact dimensions and quiet operation were also important.

The machine builder and other key suppliers worked together with Yaskawa’s automation specialists to retrofit the machine for fitting the protective caps. A total of three 400 V servo axes, each with 400 W of power, are now in use in the machine. One drive is responsible for the horizontal movement of the feed while a pneumatic linear unit with a gripper transfers the plastic cap from the separation unit to the nest of the rotary table.

An electrical cylinder driven by second servo drive presses the cap against the chair roller, while a compression force sensor detects the surge in force when they engage. Together with the absolute position sensor on the servo motor, it detects whether the pressing process was successful, while a third servo drive controls the horizontal movement. The finished parts are sent down a chute where the wheels, which are now protected by the caps, are transferred to a lattice box so they can be transported for final assembly.

The drives offer high resolution (with an integrated 24-bit absolute encoder) and high dynamics along with vibration suppression, also suppression of machine resonance frequencies and a tuning-less function for simple start-up, all integrated into the compact servo amplifiers. 

More at: https://www.yaskawa.eu.com/header-meta/news-events/article/servo-technology-for-greater-performance_n19243

Contact: Jason Louth, YASKAWA.  Tel: +44 (0) 330 678 1990 www.Yaskawa.co.uk   

More than 100 years of commitment to technical progress has made us the leading Manufacturer of variable AC drives, servo drives, machine controllers, PLCs, HMIs, as well as supplying customer-specific drive and control systems. We are driven by the vision of a smarter future developing advanced technologies that save precious time and energy. Based in Eschborn, Germany, Yaskawa Europe offers mechatronics and robotic solutions for companies throughout Europe, the Middle East and Africa. With subsidiaries in these regions and European production sites, means we are where our customers need us.

Looking at the companies involved in this there is no UK input, apart from the inevitable subsidies of course. The statement about UK becoming a global-leader through this is disingenuous. ...

Interesting - what's the hold-up? Where else in the world is this done or even planned?

It seems to me that they have worked out how to predict the position of the actuator effector, by measuring the relationship between fluid pressure and position. It is open loop control not closed...

A similar comparison is all the more devastating, in regard to the state funding of industrial R&I. e.g. The UK support for one specific invention = £125!! The award through DARPA for the very same...

Good points, Mark, despite my reservations about hydrogen. My concern about the focus on the finance sector in the UK is that the sector was built on investing the profits made by UK overseas...