Light-emitting diode lamps are more expensive but are brighter and more efficient than incandescent or fluorescent.
The Double S Dairy team uses curtain baffles so air flow can be adjusted based on in-barn temperature. At 60 degrees Fahrenheit, all 58 variable-speed fans – each 60 inches – are programmed to provide adequate airflow at maximum efficiency.
A freestall barn at Lohr Dairy is tunnel-ventilated with a bank of fans on an end wall.
Fans are thermostatically controlled in a freestall barn at Leeds Dairy. The facility was constructed by Fox Cities Builders.
A row of fans are connected to a dairy barn's power system to help keep cows from overheating.
A vacuum pump operates during milking and equipment washing and is often the primary electrical energy user.
A well-water precooler, far right, cuts compressor use by using groundwater to pre-cool the milk.
Circulation fans help improve air movement inside a barn.
Dave Ryan, National Center for Appropriate Technology energy engineer, performs a farm energy audit.
Tunnel ventilation and recycled sand keep cows comfortable inside dairy facilities at Ebert Enterprises, the Algoma, Wisconsin, farm that hosted the 2017 Wisconsin Farm Technology Days.
Wind speed should be at least 7 miles per hour anywhere cows congregate such as holding pens.
Hoffman Farms is a 300-plus-head dairy with 800 acres just west of Chatfield, Minnesota. Hoffman Farms saved energy and money on dairy technology through People’s Energy Cooperative energy-savings rebates. By placing a variable-frequency drive on a 15-horsepower milk pump, the dairy is saving 25,590 kilowatt hours during a 4,000-hour annual run time and $450 in energy rebates. Switching their dairy-parlor lights to light-emitting diodes resulted in excellent savings as well. Changing 26 two-lamp fixtures from T-8 fluorescent bulbs to linear light-emitting-diode bulbs saved 3,333 kilowatt hours and $312 in energy rebates, and another 42 T-8 fluorescent bulbs in different fixtures to linear light-emitting diodes saved 1,116 kilowatt hours and resulted in $168 in energy rebates.
Increasing energy costs and environmental concerns are causing dairy farmers to alter their management practices. Dairy farmers are analyzing their energy inputs and investing in cost-effective energy conservation and energy-efficiency measures. This publication provides an overview of how dairy farms can implement efficiency improvements and energy-saving technologies that can reduce energy consumption and energy-related costs.
Dairy farms face challenges and opportunities fueled by rapidly increasing energy costs and concerns about environmental impacts. Dairy farms use more energy than almost any other agricultural operation. Energy is used in the milking process, and for cooling and storing milk, as well as for heating water, lighting and ventilation. Determining the best energy efficiency and energy-management opportunities for dairy farms will help reduce energy costs, enhance environmental quality, and increase productivity and profitability.
Energy efficiency is often an inexpensive, quick and simple way to save money. This publication focuses on dairy-equipment upgrades, new technologies and management practices for reducing energy consumption.
Opportunities for cost savings and improved processes include the implementation of
Information regarding energy audits, financial incentives and further resources is included. The opportunities presented in this publication were developed for cow dairies but may be applicable to goat and sheep dairies as well.
Consider milking processThe milking process consists of harvesting milk from the dairy cow and transporting the milk to a bulk tank for storage. This process can take place one or two or more times per day; most dairies schedule their lactations for a continuous milk supply throughout the year. On average, milking utilizes 18 percent of the electrical energy use on a dairy farm.
Vacuum pumps have large energy requirementsThe vacuum pump operates during the milk harvest and equipment washing; it can consume 20 percent to 25 percent of all electrical energy use on a dairy farm. The vacuum pump creates negative air pressure that draws milk from the cow and assists in the milk flow from the milk receiver to either the bulk tank or the receiver bowl. The airflow also sends water and cleaning agents through the milking system during the washing process.
There are four main types of vacuum pumps – sliding vane rotary pumps, water-ring pumps, rotary lobe or blower pumps, and turbine pumps. Each of these operates and uses energy differently. Vacuum pumps become less efficient as the vacuum level increases. Therefore operating the vacuum pump at reduced vacuum levels conserves energy.
Sizing the vacuum pump to meet the needs of the milking and washing system can reduce capital costs for equipment, reduce energy operating costs during the life cycle of the pump and ensure the pump is performing properly. The size of the vacuum pump is dependent on all of the components in the system that admit air during operation. Pumps are generally sized by accounting for the amount of air admitted into the milking system during the milk harvest – plus a 50 percent reserve to account for accidental air admittance, and the wear and tear of parts. Outdated industry standards would recommend oversized vacuum pumps in part because of an incorrect belief that additional vacuum capacity is necessary for washing. An oversized vacuum pump may overheat as the pump ends its cycle. The current industry performance standard, ASAE Standard S518.2 Feb03, Milking Machine Installations, provides current sizing guidelines for dairy vacuum pumps.
energy-efficientA variable-speed drive, also referred to as an adjustable-speed drive or variable-frequency drive, is an energy-efficient technology used for controlling the vacuum level on sliding-vane rotary pumps and rotary-lobe pumps. Traditional vacuum systems run at maximum speed only; they rely on a vacuum regulator to vent excess air that is not being used during milking or washing operations. A variable-speed drive adjusts the speed of the pump motor to meet the vacuum demand so that equal amounts of air are being removed by the vacuum pump and entering the milking system. By eliminating the amount of air that would be admitted through a regulator, the motor uses less horsepower during most of the milking process. A variable-speed drive on a vacuum pump eliminates the need for a conventional regulator because less energy is delivered to the motor and its operating speeds are reduced. Energy operating costs of a vacuum system with a variable-speed drive can be reduced by as much as 60 percent. In addition, reducing the vacuum pump’s RPMs can extend its life because there will be less wear and maintenance costs.
maintenance importantFollowing the manufacturer’s maintenance schedule, along with routine maintenance on all vacuum-pump systems, can save energy. Checking the temperature of the vacuum pump near the end of each milking is a good way to detect problems with the pump or electrical load. High motor temperatures may indicate the need for a vacuum adjustment, removal of exhaust restrictions, repair of rotary-vane oiling systems or cleaning lobe-blower pumps. Changes in the speed of the vacuum pump can be caused by air leaks in the milking system, degraded drain seals, loose pump belts, malfunctioning pulsators or a malfunctioning variable-speed-drive vacuum sensor. A 5-cubic-foot-per-minute air leak in the vacuum system can amount to more than $100 in wasted electrical costs as of 2008. Problems associated with vacuum pumps can be avoided by regularly checking vacuum levels and the operation of the variable-speed drive.
use most energyCooling milk accounts for most of the electrical-energy consumption on a dairy farm. Milk is harvested from a cow at about 95 to 99 degrees Fahrenheit. To maintain excellent milk quality, including low bacteria counts, the raw milk temperature needs to be reduced quickly to about 38 degrees. Refrigeration systems consist of a bulk tank, a motor-driven compressor unit, an evaporator and a condenser unit. The system operates by pumping a refrigeration coolant in a cycle that gives off heat as it condenses. Heat exchangers cooled by well water, variable-speed drives on the milk pump, refrigeration heat-recovery units and scroll compressors are all energy-conservation technologies that can reduce the energy consumed in the cooling system.
There are two types of milk cooling systems used on dairy farms. A direct-expansion cooling system cools the milk directly in the bulk tank by using evaporator plates that expand in the lower portion of the tank. Indirect or instant cooling systems rely on heat exchangers to precool the milk before it enters the bulk tank. A precooling heat exchanger can reduce milk temperatures as much as 40 degrees, resulting in refrigeration-energy reductions of about 60 percent.
precool milkHeat exchangers used for precooling raw milk transfer the heat from the milk to an intermediate cooling fluid – such as well water or a water-glycol solution – by having the milk and coolant flow in concurrent or counterflow configurations. In a concurrent flow configuration, the milk and coolant flow in the same direction. The fluids flow in opposite directions in a counterflow pattern. Counterflow systems allow for cooler milk temperatures. The amount of cooling that takes place depends on the flow of the milk in relation to the flow of the coolant in addition to the heat-transfer area, the number of times the milk passes through the coolant and the temperature of the coolant.
Well-water heat exchangers have been implemented in precooling systems for more than 20 years and can reduce cooling costs by 0.2 to 0.3 kilowatt hours per hundredweight of milk. There are two types of heat exchangers used for precooling – shell-and-tube heat exchangers and plate heat exchangers. Shell-and-tube heat exchangers consist of a single small tube or multiple small tubes inside of a larger tube. The milk flows through the smaller tube(s) while the well water flows through the larger tube. Plate heat exchangers are comprised of a series of metal plates that are located side by side. Milk and well water run in opposite flow channels; the well water absorbs the heat from the milk on the opposite side of each plate. Plate heat exchangers are relatively small in size and, unlike shell-and-tube heat exchangers, additional plates can be added to increase capacity.
Heat exchangers are designed so that the milk and coolant make single or multiple passes between the plates or tubes. In a single-pass heat exchanger, a circuit is arranged so the two fluids are in contact as they go through separate sets of plates or tubes before exiting the heat exchanger. Multiple-pass heat exchangers route the milk and coolant flow through two or more circuits, putting the milk channels in contact with the coolant channels for longer periods of time. A heat exchanger can be designed so the milk travels through multiple circuits and the coolant flows through a single pass or circuit. Farms that milk for long periods of time can use heat exchangers that are designed for two coolants. The use of two different cooling fluids, such as first precooling with well water and then with chilled water or a glycol-water solution, can cool the milk as it is harvested.
Precooler saves energyInstalling a properly sized precooler can reduce refrigeration energy consumption by about 60 percent. A properly sized well-water heat exchanger can reduce milk temperatures to within 5 to 10 degrees of the groundwater temperature. Higher efficiency for precooling can be achieved with a 1-1 ratio of coolant to milk flow, and by using the largest water lines possible in order to maximize the coolant flow. Other factors that determine the energy and economic savings of a precooler include herd size, number and size of compressors, type of coolant used and the age of the bulk tank. An added benefit of using water for precooling is that it can afterward be used for livestock drinking water. Cows depend on drinking water to produce milk and prefer warm water to cold. The warm water can also be used to perform other tasks such as washing and heating.
reduce energy needsAs previously stated, a vacuum is required to harvest milk. The milk, however, cannot transfer from a pipeline that is under a vacuum to a bulk tank that is at normal atmospheric pressure. To compensate for the difference in pressure, milk can flow into a receiver bowl that triggers a milk-transfer pump to push the milk from the receiver bowl either through a heat exchanger or directly into the bulk tank. Another option that eliminates the receiver bowl and milk-transfer pump requires putting the bulk tank under a vacuum by placing rubber seals on the bulk-tank covers.
A variable-speed milk-transfer pump can further reduce energy use by slowing the flow rate of milk through the heat exchanger. A lower and more continuous milk flow rate through the heat exchanger increases the coolant-to-milk ratio and results in greater milk cooling. Milk can be cooled by an additional 15 to 20 degrees by installing a variable-speed milk transfer pump.
Refrigeration recovery units capture heatRefrigeration heat-recovery units capture the waste refrigeration heat from the condenser to preheat water before it is transferred to a water heater. A refrigeration heat-recovery unit can recover 20 percent to 60 percent of the energy that’s required to cool milk for storage. Depending on the number of cows being milked, the refrigeration heat-recovery unit’s storage tank should be sized to provide enough hot water for one milking. This includes hot water for washing the milking system and for washing the bulk tank. The payback for purchasing a refrigeration heat-recovery unit depends on the savings from heating water and will vary greatly from farm to farm.
Heat-recovery units inexpensiveThere are two types of refrigeration heat-recovery units – desuperheating and fully condensing units. A desuperheating unit operates only when the refrigeration system operates and produces water temperatures of about 95 to 115 degrees. These units can be inexpensive to add but only part of the available heat can be transferred to the water. Almost all the available refrigeration heat is recovered as hot water from a fully condensing unit, with temperatures reaching 120 to 140 degrees. This type of refrigeration heat-recovery unit meets the requirements of the cooling system by using a valve to control the flow of cold water through the heat exchanger. Once the storage tank is full, excess warm water can continue to be used and not wasted. A fully condensing refrigeration-heat-recovery unit replaces the need for a regular condenser in the refrigeration system and is best integrated as part of a new or replacement refrigeration system. If almost all the energy captured by the refrigeration heat-recovery unit is used for preheating water, then a precooler is not needed to remove heat from the milk and may, in fact, increase overall energy costs.
Compressors varyThe function of a compressor is to compress the cold low-pressure refrigerant gas from the evaporator to a high-pressure high-temperature state for condensing. The three types of refrigeration compressors used for milk cooling on dairy farms are the reciprocating, scroll and discus.
Hot water essentialHot water is essential for producing excellent-quality milk on dairy farms and is primarily used for cleaning milking systems. The amount of hot water required varies from farm to farm; it depends on the size of the milking herd, and the type and size of the milking system. On average a minimum of 4 gallons of water at 170 degrees are required for each milking unit. Hot water is generally produced by water heaters that use either fuel oil, natural or propane gas, solar energy or electricity. For some dairy farms, heating water can account for about 25 percent of the total energy used on the farm.
There are several ways to reduce the amount of energy used for heating water. Whether using a direct or indirect water heater, overall efficiency is determined by the combustion efficiency of the fuel source and the amount of heat loss from the storage tank – known as standby loss. A direct water heater combines the water-storage tank and the heating element. The storage tank in an indirect water heater contains a heat exchanger that is connected to a separate boiler unit. Insulating the storage tank and connecting pipes can reduce standby losses for both types of water heaters. The sides and top of an electric water heater, and the sides of gas and oil water heaters, can be insulated.
Water temperatures importantProper water temperatures are essential for cleaning milking equipment. Using warm or cold water when possible can help reduce energy costs. A warm-water pre-rinse, about 95 to 110 degrees, does not cause the milk to stick to the equipment, which is a problem with cold water. Additionally, a warm-water rinse does not cause mineral and protein deposits in the pipeline, as is often the case when using hot water. The wash cycle requires water temperatures between 120 and 170 degrees. Dairy farms require the use of commercial water heaters because residential electric water heaters are thermostatically controlled not to go warmer than 140 degrees because of federal safety regulations. The thermostat range for commercial water heaters is 100 to 180 degrees.
A cold acid rinse will control mineral and bacterial buildup in the milk lines and will help conserve hot water. There are many types of dairy acid sanitizers and each one may have different rinse instructions. Most of these sanitizers are not listed on the National List of Allowed and Prohibited Substances for use in certified organic production and processing – for the National Organic Program – but some may be permitted for use on organic dairies. Check with an organic certifier to see if they have any restrictions for use of dairy acid sanitizers.
Using a control device for electric water heaters can reduce electricity use during periods of expected increases in demand to more than the average supply level, also known as peak demand. Time clocks provide a simple and cost-effective way to control water heaters. Shifting electrical loads to off-peak or reduced-demand hours and off-peak utility rates not only ensures farmers of having hot water at a reasonable cost, but also benefits the utility provider by allowing direct control of the energy demand on their system. Many utility companies offer incentive rates or rebates to encourage farmers to participate in electric-water-heater control programs. Not all utility companies offer off-peak utility rates, so it is best to check with local service providers to see if off-peak rates are available.
Lighting improves productivity, safetyAppropriate lighting can improve productivity and safety on a dairy farm. On average, lighting represents 17 percent of total dairy farm electrical energy use. Optimal lighting conditions may increase milk productivity and conserve energy consumption. Factors that contribute to increased milk production include the type of light, the amount of light provided per watt, the temperature of the work area, the height of the ceilings and the length of the lighting period.
Lighting requirements on a dairy farm can be divided into three categories. The first category is visually intensive task lighting, which requires the highest lighting levels. Areas that benefit from this type of lighting include milking parlors; equipment washing, equipment maintenance and repair areas; offices; maternity and veterinary-treatment areas; and utility rooms. The second category includes lighting for holding areas, feeding areas, animal sorting and observation, and general cleanup. These areas and tasks require high to moderate lighting levels. Finally, low to moderate lighting levels are adequate for general lighting for livestock resting areas, passageway lighting, general room lighting, and indoor and outdoor security lighting.
There are three types of lighting systems used on dairy farms – incandescent lamps, fluorescent lamps and high-intensity discharge lamps.
Incandescent lamps – Incandescent lamps are common on many dairy farms, although today they are considered to be an inefficient light source. Their light output is only 10 percent, with the remaining 90 percent of energy given off as heat.
Fluorescent lights – Fluorescent lights are made of a frame, ballast, light socket and the lamp(s). Ballasts provide the needed voltage, current and waveform for starting and operating fluorescent and high-intensity discharge lamps. The lamps are available in many different lengths and diameters, shapes, color-temperature ratings and minimum operating-temperature ranges. Fluorescent lamps range in length from 6 to 96 inches long. The diameter of the lamp is expressed in eighths of an inch. Lamps come in the following diameters – T-5, T-6, T-8, T-9, T-10, T-12 and T-17. A T-12 lamp is 12/8 inch, or 1.5 inches, in diameter, while a T-8 is 8/8 inch, or 1 inch in diameter.
Fluorescent lamps are linear or straight, circular or U-shaped. The color-temperature index, or CCT, refers to the color appearance of the light emitted by a lamp. It is indicated in degrees Kelvin or K. Cooler temperature values produce a red or orange color, and refer to a warm emitted light. Warmer temperature values produce a blue, or cool, light source. The CCT values for fluorescent lamps range from 3,000 to 5,000 degrees K, while the average CCT value of an incandescent lamp is about 2,800 degrees K. Minimum operating temperatures for fluorescent lamps are between -20 and 50 degrees Fahrenheit, depending on whether the ballast is electromagnetic or the more-energy-efficient electric type.
The most common type of fluorescent lamp is the T-12. However, smaller-diameter lamps provide more light for a watt of power. Compared to a T-12 lamp and ballast, the T-8 fluorescent lamp provides about 15 percent more light, or lumens, and the ballasts are 40 percent more efficient. The most energy-efficient fluorescent lamp is the T-5, but that lamp tends to produce too much heat in an enclosed fixture. Enclosing fixtures in agriculture lighting systems protects the housing from corrosion, and protects the lamp from dust, humidity and manure gases, all of which can shorten the life of a lamp.
A compact fluorescent lamp or CFL uses about 75 percent less energy, measured in watts, for the same amount of light as an incandescent bulb. CFLs are directly interchangeable with incandescent lamps, so changing a 60-watt incandescent lamp to a 20-watt CFL cuts energy use by one third. CFLs also last six to 10 times longer than incandescent light sources. CFLs can be used outdoors, but should be covered to protect the lamps from all weather conditions. Cold temperatures, both indoors and outdoors, may reduce light levels. In order to reach full output at cooler temperatures, CFLs require a warm-up period.
High intensity discharge or HID lamps are a very bright and efficient light source. HID lamps often require a warm-up period and generate light by heating a gas mixture in the lamp. HID lamps must be mounted high in order to spread the light and to avoid a glare. Some HID fixtures can be equipped with a diffuser that distributes the light horizontally. The four common types of HID lights are mercury vapor, metal halide, high-pressure sodium and low-pressure sodium.
1. Mercury-vapor lamps emit a favorable blue-white color that mimics daylight. However, mercury vapor lamps are the least efficient of the HID lamps, emitting only 32 lumens for a watt. In addition, their disposal poses an environmental risk due to the mercury gas.
2. Metal-halide HID lamps provide the best color of all the HID lamps and emit about 60 lumens a watt, making them twice as efficient as a mercury-vapor lamp. A newer pulse-start lamp technology is available for metal-halide lamps. The pulse-start system can extend lamp life by half as compared to the standard metal-halide lamp, provide about 8 percent more lumens per watt, and allow for faster warmups and restarts. Pulse-start metal-halide lamps use a different type of ballast and are not interchangeable with standard metal-halide lamps.
3. High- and low-pressure sodium lamps are slightly more efficient than metal-halide lamps. High-pressure sodium lamps emit about 95 lumens a watt and give off an orange light. A 100-watt high-pressure sodium lamp can provide 2.5 times more light than a 100-watt mercury-vapor lamp while using significantly less energy. High-pressure sodium lamps are often used for mixed outdoor and indoor lighting applications. Low-pressure sodium lamps are the most efficient HID light source, but produce a poor color of light. Low-pressure sodium lamps are often used for outdoor security lighting.
Replacing inefficient light sources with an appropriate and higher-efficiency light can result in better task lighting with energy savings that continue through the life of the lamp. Energy-conservation opportunities involve changing incandescent lamps to compact fluorescents, upgrading to smaller-diameter and more-efficient fluorescent lamps, and upgrading to HID lighting. Because lighting fixtures distribute light in different patterns, the barn layout and use should be considered in any lighting decision.
Energy savings can be achieved by using simple and inexpensive technologies that go beyond lamp replacement. Some technologies incorporate programmable logic controllers and other computer-based control systems; they include timers, dusk-to-dawn photo controllers, half-night controllers and motion detectors. New and more efficient technologies are continually being developed.
Several factors can shorten the life of a lamp.
increases productionLong-day lighting is a new development for dairy farms that involves increasing milk production by extending the day length with artificial light. According to researchers, dairy cows are day-length sensitive and can be stimulated to increase milk production by providing 16 to 18 hours of uninterrupted lighting followed by six to eight hours of darkness. By implementing an efficient long-day lighting system, milk production can be increased by 5 percent to 16 percent.’
Proper ventilation criticalProper ventilation is needed in dairy barns throughout the year to help maintain animal health and productivity, the barn’s structural integrity, milk quality and a comfortable work environment for the laborers. The air inside a barn becomes warm and humid because cows continuously produce heat and moisture. An efficient ventilation system brings fresh air that is cooler and drier into the barn; it mixes and circulates it, and exhausts and dilutes moisture, dust, manure gases and odors, and airborne contaminates.
Cows that are exposed to fresh air are less likely to develop heat stress, respiratory ailments, mastitis, reproductive problems and other diseases that could decrease milk production. Many dairy producers are realizing the inherent benefits of a grass-based product ion system. Grass-based dairies utilize an ecological approach to health care by relying on natural immunity that comes with pasture access. According to experts, heat stress in dairy cows begins when surrounding temperatures exceed 65 degrees and the relative humidity is 40 percent or more. Maintaining a healthy atmosphere by controlling mold, spores, dust and other irritants also helps reduce the chances of milk contamination and reduces health risks to the farmers. Good ventilation also reduces building deterioration due to excess moisture, which can cause rot, mildew and electrical problems.
There are two types of ventilation – natural and mechanical. Natural ventilation uses the least amount of energy and requires the exchange of air, the ability to control ventilation rates, flexibility to provide the cows a comfortable environment throughout the year and good barn construction. Barns that are in the path of prevailing winds and designed with adjustable side and end walls can take advantage of breezes and thermal buoyancy, and minimize unexpected air exchanges.
Mechanically ventilated barns require air inlets and exhaust fans opposite one another. Exhaust fans are powered by an electric motor and contain hoods, protective screens, and louvers or shutters. Each fan targets a certain area to provide uniform control of moisture and gases. Ventilation fans used in livestock buildings are typically axial flow fans, which are designed to let air pass straight through the fan parallel to the fan blade drive shaft. Traditional ventilation systems are designed with air inlets and exhaust fans placed on opposite ends of a building, whereas air inlets and exhaust fans in a cross-ventilation system are located on opposite sides of a building.
A properly designed and sized ventilation-fan system should provide the required amounts of ventilation needed to maintain a comfortable environment for the cows and the laborers during each season. The blade size and shape, fan speed in terms of revolutions per minute or rpm, motor horsepower and housing design determine how much air a fan can move. This is known as fan capacity and is measured in cubic feet per minute or cfm. The size of ventilation system needed depends on its capacity to remove excess moisture during the milder and colder months of the year while forcing cool air through the building during the summer to reduce animal heat stress. Exhaust fans range in size from 5 inches in diameter to 72 inches. Exhaust-fan motors may be as small as 1/20 horsepower and may exceed more than 50 horsepower.
Static pressure is the difference in pressure between inside and outside of a building, ventilation fan or air inlet. It is measured in inches of water or inches of mercury. The static pressure of an efficient exhaust fan should be between 0.05 and .125 inches of water; it’s measured with a manometer.
Circulation fans are mounted inside buildings to help improve air movement and to reduce dead-air spots. There are different types of circulation fans, all of which have propeller blades attached directly to a motor or to a motor-and-belt drive system. Two common types of circulator fans used in dairy housing systems are box fans and high-volume-low-speed fans or HVLS. Box-type fans generally operate at moderate to high levels of efficiency, depending on the fan diameter, with the larger diameters being more efficient.
HVLS fans are large-diameter circulation fans with diameters ranging from 8 to 24 feet. One 24-foot HVLS fan can move the same amount of air as six 48-inch high-speed box fans and can save as much as 3.3 kilowatts in an hour of operation. HVLS fans save energy by replacing existing circulation fans that are not efficient. In addition, HVLS fans tend to be quiet, reduce moisture in buildings, and reduce fly and bird populations in barns.
The Air Movement and Control Association International is an independent testing laboratory that rates fans on their ability to move air. Fans that meet certain AMCA or other reliable testing-performance criteria receive a certified rating seal of approval. This rating can be helpful to select the proper fan for an intended use.
The use of thermostats to control ventilation systems reduces energy consumption by having the fans operate only when needed. Properly located thermostats should accurately reflect the average temperature inside the building. Mounting a thermostat at least 10 feet from a fan and at least 1 foot below the ceiling reduces the thermostat’s exposure to adverse factors – such as sunlight and air intake drafts – that can alter the thermostat’s temperature reading. All control systems should be located so they cannot be bumped by the livestock.
Timer controls and moisture sensors can also be used to control ventilation rates. However, the use of these control devices may not save energy. Timer controls cycle motors on and off to meet set ventilation rates and may use more energy to start the motors from the off mode. Timer controls also create larger temperature swings. Furthermore, moisture sensors have been reported not to work adequately in barns.
Dairy ventilation systems require routine maintenance to keep fans operating at high performance levels. Poorly maintained fans and obstruction to air inlets and fan outlets can reduce fan efficiency by as much as 40 percent to 50 percent. Cleaning fan parts, lubricating bearings and other moving parts, checking belt tension and alignment, and removing any obstructions will keep fans performing at peak efficiency and reduce energy costs. Long-term efficiency can be improved by repairing or replacing bent, damaged or misaligned fan blades, shutters, guards and other fan parts. An air-velocity meter can be used to detect reductions in the performance of the ventilation system. Control systems should be cleaned regularly and thermostats should be checked yearly for accuracy by comparing their readings against a mercury thermometer.
Several factors affect the efficiency of a livestock-ventilation system.
Audit farm energy regularlyA farm-energy audit is a tool to help agricultural producers conserve energy and save money by implementing energy-efficient equipment. The audit collects and analyzes information on farm energy consumption and its associated costs, and then makes recommendations on ways to reduce them. Farm-energy audits also explore ways to capture renewable-energy resources that are available on a farm. Dairy operations are often good candidates for farm-energy audits because there are significant opportunities for dairies to save energy and money through conservation and efficiency measures. Farm-energy audits can be conducted by a professional or through do-it-yourself energy-efficiency calculators.
There are several federal, state and nonprofit grant and incentive programs for implementing energy efficiency and renewable-energy systems on dairy farms. Visit www.dsireusa.org and www.rd.usda.gov/about-rd/agencies/rural-business-cooperative-service for more information.
SummaryThere are many opportunities for dairy farms to reduce their electrical-energy consumption. Dairy farms can become more energy efficient by upgrading older equipment, installing new technologies, and changing management practices for milk harvesting, milk cooling and storing, ventilation and lighting. An energy audit can be a valuable tool to a dairy farmer who is trying to understand how energy is currently being used on the farm and identify cost-saving opportunities.
Visit www.ncat.org for more information.
Andy Pressman is an agricultural specialist with the National Center for Appropriate Technology. Visit www.ncat.org for more information.
Get local news delivered to your inbox!
Light-emitting diode lamps are more expensive but are brighter and more efficient than incandescent or fluorescent.
The Double S Dairy team uses curtain baffles so air flow can be adjusted based on in-barn temperature. At 60 degrees Fahrenheit, all 58 variable-speed fans – each 60 inches – are programmed to provide adequate airflow at maximum efficiency.
A freestall barn at Lohr Dairy is tunnel-ventilated with a bank of fans on an end wall.
Fans are thermostatically controlled in a freestall barn at Leeds Dairy. The facility was constructed by Fox Cities Builders.
A row of fans are connected to a dairy barn's power system to help keep cows from overheating.
A vacuum pump operates during milking and equipment washing and is often the primary electrical energy user.
A well-water precooler, far right, cuts compressor use by using groundwater to pre-cool the milk.
Circulation fans help improve air movement inside a barn.
Dave Ryan, National Center for Appropriate Technology energy engineer, performs a farm energy audit.
Tunnel ventilation and recycled sand keep cows comfortable inside dairy facilities at Ebert Enterprises, the Algoma, Wisconsin, farm that hosted the 2017 Wisconsin Farm Technology Days.
Wind speed should be at least 7 miles per hour anywhere cows congregate such as holding pens.
Hoffman Farms is a 300-plus-head dairy with 800 acres just west of Chatfield, Minnesota. Hoffman Farms saved energy and money on dairy technology through People’s Energy Cooperative energy-savings rebates. By placing a variable-frequency drive on a 15-horsepower milk pump, the dairy is saving 25,590 kilowatt hours during a 4,000-hour annual run time and $450 in energy rebates. Switching their dairy-parlor lights to light-emitting diodes resulted in excellent savings as well. Changing 26 two-lamp fixtures from T-8 fluorescent bulbs to linear light-emitting-diode bulbs saved 3,333 kilowatt hours and $312 in energy rebates, and another 42 T-8 fluorescent bulbs in different fixtures to linear light-emitting diodes saved 1,116 kilowatt hours and resulted in $168 in energy rebates.
Get up-to-the-minute news sent straight to your device.